Gas Dryer Repair · Round Rock, TX · Open 24/7
Gas Dryer Repair in Round Rock, TX: Ignition, Gas Valve and No-Heat Fixes, Day or Night
Gas dryers fail differently from electric ones. When the drum turns but the air stays cold, the fault is almost always in the ignition system: the igniter, the flame sensor or the gas valve coils. Our technicians test each part with a meter instead of guessing, carry the common gas parts on the truck, and leak-check every connection before they leave.
- Open 24/7
- Leak check on every visit
- $79 diagnostic waived with repair
- 12-month parts and labor guarantee
Quick answer
Why is my gas dryer not heating?
A gas dryer that tumbles but will not heat usually has a failed igniter, weak gas valve coils or a bad flame sensor. Less often, a blown thermal fuse has cut the burner circuit, which almost always points to a clogged vent. If you smell gas, stop using the dryer and leave the house before you call anyone.
- Most ignition repairs done in one visit
- Igniters and coils carried on the truck
- Gas connections leak-tested
- Same-day service most days
Safety first
Smell Gas Near Your Dryer? Do This Before Anything Else
Natural gas smells like rotten eggs because the utility adds an odorant. If you notice that smell around the laundry room, treat it as an emergency, not a repair.
- Leave the house right away and take everyone with you
- Do not flip light switches, unplug the dryer or use a phone indoors
- From a safe distance, call 911 and the Atmos Energy emergency line:
866-322-8667 - Once the utility has made the area safe, call us to repair the dryer
How it works
How a Gas Dryer Makes Heat, in Five Steps
Every gas dryer, from a 20-year-old Whirlpool to a new Samsung, lights its burner the same way. Knowing the sequence makes it easy to see which part has failed.
1. The Thermostat Calls for Heat
When you start a heated cycle, the cycling thermostat and controls send power to the burner circuit through the thermal fuse and high-limit thermostat.
2. The Igniter Glows
The igniter, a small silicon carbide or silicon nitride element, heats up until it glows bright orange, well above 1,800°F. This takes 30 to 90 seconds.
3. The Flame Sensor Reacts
The flame sensor, mounted on the burner tube, feels that heat and opens its circuit. That change is the signal for the gas valve to release gas.
4. The Gas Valve Coils Open
Two or three small electric coils on the gas valve open the valve. Gas flows down the burner tube, meets the glowing igniter, and lights.
5. The Burner Cycles On and Off
Once the drum reaches temperature, the cycling thermostat shuts the flame off, then relights it as the air cools. A healthy dryer repeats this many times per load.
Where It Usually Breaks
In our experience, the igniter and the gas valve coils account for most gas dryer no-heat calls. The flame sensor and thermal fuse come next.
Is there a reset button on a gas dryer?
Most gas dryers have no reset button for the heating system. The thermal fuse is a one-time safety part that must be replaced once it blows. To clear a control glitch, unplug the dryer or switch off its breaker for one minute, then restart it. Some commercial and older models differ.
What would cause no heat on the second dryer cycle but not the first?
A commercial-dryer tech on AppliancePartsPros flagged this pattern: the igniter heats the first cycle fine, then needs time to cool before it ignites again. Waiting a few minutes between cycles let the reported dryer heat normally on the next run.
Common problems
Gas Dryer Problems We Fix Most Often in Round Rock
Each of these has a different cause, so the symptom you describe on the phone helps us bring the right part on the first trip.
The Igniter Never Glows
If you can look through the small window or burner opening and see no orange glow, the igniter has usually cracked or burned through. We confirm it with a continuity test before replacing it.
It Glows, Then Clicks Off
The igniter glows, goes dark, and no flame appears. This classic pattern points to weak gas valve coils that can no longer hold the valve open once they warm up.
Flame Lights, Then Goes Out
The burner lights for a few seconds and then shuts off, over and over, while the clothes stay damp. Failing coils or a flame sensor that is closing too early are the usual causes.
The Igniter Stays On
An igniter that glows constantly without ever lighting the burner usually means the flame sensor is stuck closed. Left alone, it will burn out a brand-new igniter quickly.
No Heat at All, Drum Still Turns
When nothing in the burner circuit gets power, the thermal fuse or high-limit thermostat has usually tripped. We replace the part and find out why the dryer overheated.
Weak, Yellow or Noisy Flame
A healthy gas flame burns mostly blue. A lazy yellow flame, a roaring sound, or soot near the burner points to an air shutter, orifice or supply pressure problem that needs a closer look.
Not sure which one you have? Describe what you see and hear on the phone, and we will tell you the most likely part before we arrive.
What are the most common parts that fail on a gas dryer?
The five parts we replace most are the igniter, the gas valve coils, the flame sensor, the thermal fuse and the cycling thermostat. All sit in the heating circuit, so a failure in any one of them leaves the drum tumbling with no heat. Belts and drum rollers are the next most common.
Diagnosis
Gas Dryer Symptom Chart: What Fails and How We Test It
Match what your dryer is doing to the most likely cause. A good technician confirms the part with a meter reading before ordering anything, so you never pay for parts you did not need.
| What you notice | Most likely cause | How we confirm it |
|---|---|---|
| Drum turns, no glow, no heat | Igniter or thermal fuse | Continuity test on each part |
| Igniter glows, then no flame | Gas valve coils | Coil resistance reading |
| Flame lights, then drops out | Gas valve coils or flame sensor | Watch the cycle, test both parts |
| Igniter glows nonstop | Flame sensor stuck closed | Continuity test while hot |
| Heats a little, clothes still damp | Cycling thermostat or restricted vent | Temperature reading and airflow check |
| Dryer will not start at all | Door switch, start switch or motor | Voltage checks at the controls |
| Gas smell when running | Loose connector or valve fitting | Electronic leak detector and soap test |
Is it normal for a gas dryer’s igniter to glow orange?
Yes, briefly. iFixit’s gas dryer guide notes the igniter should glow bright orange for about 30 to 45 seconds before the gas valve opens. If it glows but the burner never lights, the valve coils are the more likely failure, not the igniter itself.
Gas versus electric
What Makes Gas Dryer Repair Different
An electric dryer heats with a coiled element on a 240-volt circuit. A gas dryer uses a standard 120-volt outlet to run the motor, controls and igniter, then burns natural gas or propane for heat. That means a gas dryer has more parts in the heating system, and every one of them sits close to an open flame.
It also means a gas dryer repair is partly a safety visit. Any time a technician opens the burner area, the gas connections should be checked for leaks, the flame should be watched through a full cycle, and the vent should be confirmed clear so exhaust leaves the house. A clogged vent on a gas dryer does more than slow drying; it can push combustion gases back indoors. If yours is restricted, see our dryer vent cleaning service.
Included in Every Gas Dryer Visit
- Meter testing of the igniter, flame sensor and valve coils
- A full heating cycle watched from first glow to shutoff
- Flame color and burner condition checked
- Leak test on the valve, connector and shutoff fittings
- Flexible gas connector inspected for age and kinks
- Airflow at the vent confirmed before we leave
- A clear, written price before any repair begins
How do I check the gas supply to my dryer?
Look at the shutoff valve on the pipe behind the dryer. The handle should run parallel to the pipe, which means open. Check that the flexible connector is not kinked and that other gas appliances work. Never test for leaks with a flame. If you smell gas, leave and call for help.
Pricing
How Much Does Gas Dryer Repair Cost in Round Rock?
Gas dryer repair in Round Rock usually costs $140 to $260 including the part and labor, because the usual culprits, the igniter, flame sensor and valve coils, are small parts that install in under an hour. Burner assembly and control board repairs run higher. The $79 diagnostic is waived when you go ahead with the repair.
| Gas dryer repair | Typical total cost | Usual time |
|---|---|---|
| Igniter replacement | $150 to $250 | 30 to 45 min |
| Gas valve coil set | $160 to $260 | 30 to 45 min |
| Flame sensor | $140 to $230 | About 30 min |
| Thermal fuse or high-limit thermostat | $100 to $200 | About 30 min |
| Cycling thermostat | $140 to $230 | About 30 min |
| Flexible gas connector replacement | $120 to $200 | About 30 min |
| Burner assembly or gas valve | $250 to $400 | 60 to 90 min |
Prices include the part, labor and a leak test. Your technician confirms the exact price in writing before starting, and every repair carries our 12-month parts and labor guarantee.
Smelling gas or just no heat?
Know What You’re Dealing With Before We Arrive
Tell us whether you smell gas or just have no heat — that one detail changes how urgently we dispatch and what we bring on the truck.
Local know-how
Gas Dryers in Round Rock Homes: What We See
Atmos Energy supplies natural gas across Round Rock, and many homes built from the 1990s on have a gas stub in the laundry room. A few local patterns shape how we handle gas dryer repair in Round Rock.
Garage Laundry Rooms
Many Round Rock homes put the washer and dryer in the garage. Summer garage heat pushes the dryer to its high-limit thermostat sooner, and blown thermal fuses are more common in July and August than any other time of year.
Aging Gas Connectors
The flexible connector behind the dryer wears out, especially when the dryer is pushed against the wall and kinked. Very old uncoated brass connectors are a known safety concern and should be replaced, not reused.
Propane on the Edge of Town
Some homes on rural land around Round Rock run on propane instead of natural gas. A propane dryer needs a conversion kit with different orifices, and a dryer moved between the two fuels without one will burn poorly.
Switching From Electric to Gas
Homeowners replacing an electric dryer sometimes discover the gas stub was capped years ago. We install the dryer and connector; new gas piping is handled by a licensed plumber, as Texas requires.
Brands
Gas Dryer Brands We Repair
Whirlpool builds Maytag, Kenmore, Amana and KitchenAid gas dryers on shared platforms, so the same igniters and coils fit a large share of the dryers in Round Rock laundry rooms.
- Whirlpool
- Maytag
- Kenmore
- GE
- Samsung
- LG
- Frigidaire
- Electrolux
- Amana
- KitchenAid
- Speed Queen
- Bosch
FAQ
Gas Dryer Repair Questions, Answered
Why does my gas dryer igniter glow but never light?
When the igniter glows and then goes dark with no flame, worn gas valve coils are the usual cause. They weaken with heat and stop holding the valve open. A weak igniter that glows red instead of bright orange can cause the same symptom, so a technician tests both before replacing either.
Why is my gas dryer only blowing cold air?
A gas dryer that blows cold air usually has a failed igniter, weak valve coils, a bad flame sensor or a blown thermal fuse. A closed gas shutoff valve or a no-heat cycle setting can also be the cause. Check those two first, then call for testing of the ignition parts.
How long does a gas dryer last?
Most gas dryers last 10 to 13 years with normal use and yearly vent cleaning. Ignition parts are designed to be replaced, so an igniter or coil failure on an older dryer is usually worth fixing if the drum, motor and cabinet are still in good shape.
Is it safe to keep using a gas dryer that smells like gas?
No. A brief whiff at ignition can be normal, but a smell that lingers means gas is escaping. Stop using the dryer, leave the house, and call 911 and Atmos Energy at 866-322-8667 from outside. Book the repair only after the area has been made safe.
Does a gas dryer need an electrical outlet?
Yes. A gas dryer plugs into a standard 120-volt outlet to power the drum motor, controls and igniter. Only the heat comes from gas. That is why a gas dryer does not need the large 240-volt outlet an electric dryer uses, and why a tripped breaker can stop it completely.
We pick up 24/7
Get Your Gas Dryer Heating Again
Call any time, day or night, for gas dryer repair in Round Rock and nearby neighborhoods. You get a meter-tested diagnosis, a written price before work starts, a leak check on every connection, and a 12-month parts and labor guarantee.